DICTATOR door checks       Nederlandse vlagschakel naar Nederlands

DICTATOR door checks, the real answer to slamming doors
noiselessly control the closing of your doors, no more door slamming.


1)
DICTATOR door checks put an end to slamming doors because they catch the door thrown shut by hand, by a closing spring or by a gust of wind just before the "great bang" and then pull it quietly and safely to the completely closed position.

For this reason they are ideal e.g. in hospitals, public buildings, hotels, offices and many other buildings. DICTATOR door checks have also proven to be the ideal solution in very sensible areas where every shaking may damage precious equipment, e.g. in research laboratories.

2) DICTATOR door checks make sure doors will be completely closed thus contribute to more energy efficiency and safety.

Also the ideal addition to an overhead door closer when there are problems closing the door due to influences of the wind or to too much resistance caused by the door lock.

For exterior doors we have the door check type 1400 for fixing on the same side as the door stop, standard also suitable for horizontal fixing.

Especially designed for sliding doors we have the door check type 1100 with a mounting bracket in Stainless Steel. This device will make sure the closing speed on the last few centimeters is slowed down and closes the sliding door completely. Below a table with the different types of door checks we can offer you for your hinged- or sliding doors.

 

Door checks for H I N G E D  D O O R S   S L I D I N G  D O O R S 
DICTATOR 1000 
DICTATOR 1600  
  
DICTATOR VS2000  
  
DICTATOR 1300 
   
DICTATOR 1400  
  
DICTATOR Junior

DICTATOR 1100  
  
DICTATOR 1700

 
1000/1200
The standard model
 for normal doors



Also approved by Warrington Fire for use on fire doors according BS 476. (WFRC No C11051)


more....
 
1600
The enclosed model
 for normal doors.



Also approved by Warrington Fire for use on fire doors according BS 476. (WFRC No C11051)

more....
 
VS2000
Design all in one line,
also suitable for heavy doors.


Also approved by Warrington Fire for use on fire doors.according BS 476. (WFRC No C11051)
more....
 
1300
For damping of extra heavy doors

more....
 
1400
For fixing to doors
on the  same side
 as the door stop.


Also approved by Warrington Fire for use on fire doors according BS 476. (WFRC No C11051)


more....
 
 Junior
Mini versie van deuropvanger trekkend (140) of duwend (160)

more....
 1100
For damping of sliding doors

more....
 1700
For damping of sliding doors, also in RAL and Stainless steel

more....

More information needed? Just click on one of the above photos to get more detailed information of the specific type of door check.

DICTATOR door checks noiselessly control the closing of doors. The door check will ensure, that the door will be held firmly closed and will not slam when shut. By making use of a DICTATOR door check, your door, door frames and windows will not be damaged anymore. The use of a door check also guarantees you that the loud bang, that normally follows after slamming the door, will no longer occur. This is certainly important at locations and buildings where silence is a must. (offices, hospitals, hotels, entrance doors in flats etc.). Also the ideal solution to prevent little fingers to get stuck between the door and the door frame since the speed of the closing of the door will be reduced significantly.

We can provide you with a solution for the different door situations (flush, recessed, projecting or sliding doors). See also productvideos below.

 

We have tested our door checks for 1 Million door cycles without any problem whatsoever.

Please check also our download section to see all other door technique solutions DICTATOR can offer you.

Looking for high quality DICTATOR lift door dampers instead? Please click here.

Wonder where you can buy these products? Just click here and easily find out where our products are distributed.

Below mentioned is a table of several types of door checks available. By clicking on a photo or a hyperlink you will get access to detailed information like description of the door check, the fitting of it and it's dimensions.

 Type  Short description  Door type  Finish
 1000/1200  basic model  all normal doors  Zinc or nickel plated
       
 1600  enclosed model  all normal doors  Chromium, Stainless steel, RAL 8017, 9005, 9006, 9010 (other RAL colors on request) and bright gold
DICTATOR 1600 RVS  DICTATOR 1600-1009 ZWART RAL 9005
Bright chromium Stainless steel Brown (RAL 8017) White (RAL 9010) Grey (RAL 9006) Black (RAL 9005) Bright gold (brass)
       
 VS2000  design model  normal and heavy doors  Chromium, RAL 8017, 9005, 9006, 9010 (other RAL colors on request) and bright gold
DICTATOR VS2000-1020 ZWART RAL 9005
Bright chromium Brown (RAL 8017) White (RAL 9010) Grey (RAL 9006) Black (RAL 9005) Bright gold (brass)
 
 1300  extra strong  heavy doors  Nickel plated
       
 1400  for exterior doors  same side as door stop  Zinc, chromium, Stainless steel, RAL 8017, 9005, 9006, 9010 (other RAL colors on request) and bright gold
DICTATOR 1400-1014 zwart RAL 9005
Bright chromium Brown (RAL 8017) White (RAL 9010) Grey (RAL 9006) Black (RAL 9005) Bright gold (brass)
       
 Junior  miniature version door check  lightweight doors/drawers  Stainless steel
       
 1100  including S.s. bracket  sliding doors  Zinc- or nickel plated
       
 1700   enclosed model, including S.s. bracket  sliding doors  Chromium, Stainless steel, RAL 8017, 9005, 9006, 9010 (other RAL colors on request) and bright gold
 DICTATOR 1700 chroom met hoekstuk RVS voor schuifdeuren  DICTATOR 1700 bruin met hoekstuk RVS voor schuifdeuren  DICTATOR 1700 wit met hoekstuk RVS voor schuifdeuren  DICTATOR 1700 grijs met hoekstuk RVS voor schuifdeuren DICTATOR 1700 zwart met hoekstuk RVS voor schuifdeuren  DICTATOR 1700 RVS met hoekstuk RVS voor schuifdeuren
Bright chromium Brown (RAL 8017) White (RAL 9010) Grey (RAL 9006) Black (RAL 9005)   Stainless steel 


Important advantages:

Adjustment of our door checks:

Using the hexagon socket screw located in the end of the piston rod, the closing speed can be increased by turning the screw anti-clockwise and decreased by turning the screw clockwise.